How should cantilever support spacing be chosen for long stock near I-795 and I-695?

Light manufacturers near Owings Mills Boulevard may keep long stock beside workstations because standard pallet rack obstructs side loading. Cantilever can put those bundles into defined arm levels, with space retained for the full-length handling move between the rack and production rather than only the rack itself. Use bundle length, weight, stiffness, and the manufacturer's design requirements rather than a fixed spacing copied from another product. Loads need enough arms to avoid sagging and balanced support. We also check pickup clearance, arm length, column capacity, and single- or double-sided access.

What information helps plan cantilever rack for a Owings Mills Boulevard building?

Owings Mills businesses often combine reserve storage with service, assembly, or regional order preparation. Along I-795 and Reisterstown Road, the best plan may use several storage types rather than one dense block. Keep measured work areas and truck access visible in the layout so added rack does not consume operational space. Send your load dimensions, weights, inventory quantities, building measurements, and current handling clearances. The space in front of the arms must accommodate the whole load during pickup. That may make a shorter wall run more useful than a larger double-sided arrangement with restricted access. Record the bundle support assumptions and capacity per arm so changes in product length or level spacing can be reviewed before loading.

How is cantilever rack different from pallet rack?

Pallet rack has a front beam and stores discrete, boxed loads. Cantilever has an open front, so long material loads from the side and slides in without clearing an obstruction - that's the entire reason the system exists.

How far apart should the columns be?

Close enough that the load doesn't sag between arms. A common starting point puts arm spacing at roughly half the load length, with the remainder overhanging each end evenly. We check that math against your heaviest bundle before finalizing spacing.

Straight arms or inclined arms?

Straight arms suit boxed, banded, or sheet goods. Inclined arms, usually fitted with a lip, keep pipe, tube, and round stock from rolling forward off the arm. Many runs mix both across different levels.

Can arms or levels be added later?

Yes. Arms mount at set increments up the column, so levels can be added or repositioned as your product mix shifts, as long as total load stays within the rated capacity of the column and base.

Does cantilever rack need to be anchored to the floor?

Yes - bases are anchored to the floor, and taller or double-sided runs get braced between columns. Anchors and bracing are priced into the quote rather than left for the installer to include in the project scope.

Can cantilever rack sit next to pallet rack in the same building?

Routinely. It's common to run cantilever along one wall for long stock and selective or another pallet system through the rest of the building - we lay out both in the same drawing so aisle widths and clearances line up.

Cantilever Rack system inside a Maryland warehouse

Owings Mills, Maryland

Cantilever Rack in Owings Mills, Maryland

Cantilever Rack in Owings Mills, MD starts with a storage problem, not a catalog choice. Light manufacturers near Owings Mills Boulevard may keep long stock beside workstations because standard pallet rack obstructs side loading. Cantilever can put those bundles into defined arm levels, with space retained for the full-length handling move between the rack and production rather than only the rack itself. Cantilever warehouse racking supports long loads on open-front arms instead of forcing them into boxed pallet bays. It can free working floor while keeping lumber, pipe, and profiles available for the next order. We plan arm capacity, support spacing, and loading access from your actual bundles and handling method, with a written layout and quote.

(410) 305-9766

Why Owings Mills Warehouses Work With Us

Owings Mills businesses often combine reserve storage with service, assembly, or regional order preparation. Along I-795 and Reisterstown Road, the best plan may use several storage types rather than one dense block. Keep measured work areas and truck access visible in the layout so added rack does not consume operational space.

We ask for the full bundle length, weight, stiffness, and pickup method before deciding column spacing. Long material needs enough supports to prevent sagging, not just a strong arm at each end. Single-sided wall runs and double-sided floor runs are compared against the space needed to approach and turn the load. The quote identifies bases, columns, arms, bracing, and anchors, with capacities tied to the finished arrangement. Installation is coordinated through partners to the approved drawing. Where long stock shares a warehouse with pallets or case picks, we plan both storage types together instead of leaving the aisle conflict for your operators. We discuss future inventory changes before finalizing the proposed arrangement and its component list.

Free Design Consultation

CAD layout with position counts

Installation by installation partners

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Operations We Rack Around Here

Industrial corridors covered by our service area include I-795 and I-695, Owings Mills Boulevard, Reisterstown Road, New Town business area.

Business-to-business distribution

Consumer products

Light manufacturing

Regional service supply

How Cantilever Rack Works

Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.

Columns and anchored bases

Upright columns sit on bases anchored to the floor. Base depth is set by load and arm length so the run stays stable even under an off-center pick.

Arms at adjustable heights

Arms bolt or pin into the column at set increments and move as your product mix changes. Straight arms suit boxed goods; inclined arms with a lip hold round or loose stock in place.

Column spacing against sag

Spacing between columns is set so bundles don't sag between arms. A common starting rule places arms about half the load length apart, with the ends overhanging evenly.

Single-sided or double-sided

Single-sided runs go against a wall. Double-sided runs stand in open floor and load from both faces, doubling capacity per base without doubling the footprint.

What a Cantilever Rack Project Includes

Cantilever specification starts and ends with the load. We collect bundle dimensions, weight per bundle, and how material is handled - lift truck forks, a side loader, or by hand off a cart - because that determines arm length, arm capacity, and how much clearance each level needs.

From there we set column height and spacing, choose straight or inclined arms, and decide whether lips are needed to keep round stock from rolling. Single-sided runs get positioned along a wall; double-sided runs get aisle dimensions matched to whatever's moving material in and out.

The quote itemizes columns, bases, arms, bracing, and anchors, with a CAD drawing showing the run, arm levels, and rated capacities per arm. Installation partners anchor bases, plumb columns, brace the run, and set arm elevations to the drawing.

The result is arms you can reposition as inventory changes, capacity ratings for every level, and the floor space that long material used to occupy.

The space in front of the arms must accommodate the whole load during pickup. That may make a shorter wall run more useful than a larger double-sided arrangement with restricted access. Record the bundle support assumptions and capacity per arm so changes in product length or level spacing can be reviewed before loading.

Lumber, plywood, and sheet goods

Pipe, tube, conduit, and bar stock

Steel service center inventory

Furniture, doors, and windows

Long or awkward loads currently sitting on the floor

Call (410) 305-9766

Recent Pallet Rack Projects

Racking projects completed for warehouses across the Baltimore metro.

View More Projects

Get a Cantilever Rack Quote for Your Owings Mills Warehouse

Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (410) 305-9766.

Baltimore Pallet Racks

1400 W. Lombard St.

Unit #687

Baltimore, MD 21223

(410) 305-9766

Monday - Friday: 8:00 AM - 6:00 PM

Name *

Company *

Email *

Phone *

Where are you located? *

Approximate warehouse size *

Expected timeframe *

Additional Information

I consent to receive SMS and email communications from Baltimore Pallet Racks regarding my quote request. Message and data rates may apply. Reply STOP to opt out.

We respect your privacy. Your information will never be shared.